White&Yellow Glue Sticks: The sufficient glue sticks(15 yellow&5 white) with each of 0.4310.6 inches in size allows for long-term use. The white glue sticks have strong viscosity and are suitable for relatively hard parts on automobiles, while the yellow glue sticks apply to relatively soft parts on automobiles. Rubber Hammer: The rubber hammer with a double-sided hammerhead design and 9Pcs accessories can reduce the vibration and rebound while using, and fix the small and irregular dents. Bridge Dent Puller: Made of good steel, the bridge dent puller is strong and won't easy to broke. Rubber tabs will protect the distance from damage.
The 6 different size tabs apply to different size dents, and you can adjust the distance of the puller's 2 sides tabs according to the shape of the car surface. The holes will make the glue adhesive easily. Dent Lifter: Made from lightweight aluminum with a powder-coated treatment, this dent lifter is durable. Its padded feet increase support for maximum pulling power without denting surrounding areas. It is mainly used for dent repairs for any vehicle.This kit applies to the use of automobile sheet metal repair machines and shaping machine. Put a glue stick to the gun, connect the power source, and preheat for 5 minutes. Choose the glue puller tab according to the dent size, then put the heated glue on it, immediately place the puller tab in the center of the dent and hold on until it sticks. Let the glue cool for 2-4 minutes. After the glue cooling, use a golden dent lifter or bridge dent puller to align and press the puller to pull up the dent.
Repeat the above steps until the dent disappears. After finishing the dent, use the alcohol to clean the glue on the car and the puller tabs.
How to Use Dent Lifter to Repair Small Dents. Clean the dent surface with a clean cloth(included). Choose a suitable tab and apply the glue to it. Put the tab at the center of the dent, press lightly until the glue cures and adheres, and wait a few minutes. Screw the rotary axis of the lifter to find a perfect range for the spring that can pull the tab out. Press the handle of the dent lifter to pull up the dent. Use the alcohol (not included) and plastic scraper to remove the glue, and clean the repaired place with a clean wet cloth.Use tap-down tools to repair bumps. How to Use Bridge Dent Puller to Repair Medium Dents.
Choose a suitable bridge puller tab and apply hot melt glue to it. Put the tab on the dent and wait a few minutes.
Adjust the three screws' height to find a perfect place for the bridge puller, then tighten the nut. Repeat the operation many times. Color: Blue, Black, Silver, Orange, etc.
Compatible Devices: Automobiles Metal Plate Repair Machine, Shaping Machine. Way of Use: Automobiles Maintenance. Glue Stick Size(DL): 11270mm/0.4310.6inch. Handbag Size: 421025cm/16.53.99.9inch. Package Size: 421728cm/16.56.711.02inch. Gross Weight: 4.5kg/9.9lbs. 10 Yellow Glue Sticks (27011mm). 5 White Glue Sticks (27011mm). 6 Black Bridge Puller Tabs.Please note that this kit should be used with a car body dent spot repair device welder. This product is equipped with an alcohol bottle but does not contain alcohol. This product is suitable for the use of the original paint vehicle. It is not recommended to use if the paint at the depression is damaged, there are scratches, or cracks, or the body has been waxed and coated, to avoid the risk of secondary strain.
If the diameter of the concave part is less than 2cm or it is a thin and long concave line, or the concave is pointed, which will cause to fall off easily due to insufficient contact between the rubber pad and the concave surface, it is not suitable for using this product. This product does not guarantee that all dents can be repaired, so please check with customer service before purchasing to see if your car can be repaired with this product. If the concave surface is not cleaned, the suction cup will be unglued easily when gluing.Please clean the concave with alcohol and dry it before the operation. Generally, it needs to be heated for more than 5 minutes and the heating time can be extended in places with low temperatures.
It is recommended to add a layer of glue on the surface of the suction cup after the bottom is filled with glue, which will be more solid. After gluing, let it cool naturally.
You can push down the glue by hand. It can be operated if it is hard to push. At normal temperature, please clean the excess glue on the car and tractor assembly with alcohol after fixing the dent. In winter(at low temperatures), heat the glue with hot water for the 30s or extend the heating time to 1min to ensure that it reaches the melting point temperature of 70? Then spray some alcohol to completely remove the glue. Please allow the slight difference caused by the shooting light and 1-3cm error due to manual measurement, and make sure you do not mind before ordering. Feedback is very important to us. It is impossible to address issues if we do not know about them! Faction is our ultimate goal. We work hard to earn your trust and future business. A If you receive a defective item, you may return it or ask for a discount. Due to time zones, our reply to your questions may not be immediately. If it's non-workdays, please kindly be patient and wait till Monday. This item is in the category "eBay Motors\Automotive Tools & Supplies\Automotive Repair Kits\Dent Repair Kits & Tools". The seller is "yylocalstock" and is located in this country: US. This item can be shipped to United States.